Metrologic MS5100 Instrukcja Naprawy Strona 21
- Strona / 48
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
17
Programming Modes
EXAMPLE #3
:
The following example shows the events that occur when an invalid bar code
is sent. This sample will load the factory default settings and then set the
baud rate to 19200.
HOST SCANNER
FEATURE
COMMAND ASCII REPRESENTATION RESPONSE
Enter Program Mode [stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ack] or 06h
Load Defaults [stx]99999:[etx] 02h 39h 39h 39h 39h 39h 3Ah 03h [nak] or 15h
Invalid command was sent, you must start over!
Enter Program Mode [stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ack] or 06h
Load Defaults [stx]999998[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ack] or 06h
19200 Baud Rate [stx]415870[etx] 02h 34h 31h 35h 38h 37h 30h 03h [ack] or 06h
Exit Program Mode [stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ack] or 06h
The scanner will beep three times!
This example illustrates two important points.
First, if an invalid command is sent from the host, the scanner responds with
a [nak] and the end-user must start over from the beginning.
Second, if a command is sent to change the Baud Rate, the new baud rate
does not take effect until after the end-user exits program mode.
ABBREVIATED ASCII TABLE
Character Hex Value Decimal Value
[STX] 02h 2
[ETX] 03h 3
[ACK] 06h 6
[NAK] 15h 21
0 30h 48
1 31h 49
2 32h 50
3 33h 51
4 34h 52
5 35h 53
6 36h 54
7 37h 55
8 38h 56
9 39h 57
- Locations 3
- ABLE OF CONTENTS 4
- INTRODUCTION 5
- SCANNER AND ACCESSORIES 6
- OPERATIONAL TEST 8
- MS5145-00/9/11/14/41 9
- Keyboard Wedge MS5145-47 10
- Figure 6 11
- USB: L 12
- FULL SPEED USB MS5145-40 12
- THE POWERLINK CABLE 13
- SCANNER PARTS 14
- THE MS5145 ECLIPSE™ SERIES 15
- AUDIBLE INDICATORS 16
- VISUAL INDICATORS 17
- FAILURE MODES 18
- Bar Codes 19
- MetroSet 19
- Serial Programming 19
- PROGRAMMING MODES 20
- Programming Modes 21
- MLPN 54-54012) are 22
- SCAN AREA 23
- LABELS 24
- APPLICATIONS AND PROTOCOLS 25
- TROUBLESHOOTING GUIDE 26
- RS232 DEMONSTRATION PROGRAM 29
- DESIGN SPECIFICATIONS 30
- DEFAULT SETTINGS 32
- 55-55000A-3 39
- LIMITED WARRANTY 41
- LASER AND PRODUCT SAFETY 42
- PATENTS 44
- 70- 79016B 48
Powiązane produkty i podręczniki dla Czytniki kodów kreskowych Metrologic MS5100
(12 strony)
(36 strony)Rugged-ridge Rear Lower Control Arm Skidplates, 07-14 Jeep Wran podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Do samochodu Rugged-ridge Rear Lower Control Arm Skidplates, 07-14 Jeep Wran.
Dostarczamy 1 pdf podręczników Rugged-ridge Rear Lower Control Arm Skidplates, 07-14 Jeep Wran do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentarze do niniejszej Instrukcji