Metrologic StratosS MS2220 Podręcznik Użytkownika Strona 26
- Strona / 68
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
22
INSTALLATION
CABLE INSTALLATION (INTERFACE SPECIFIC)
OCIA
The following steps describe how to properly install the cables for an OCIA StratosS application. The scanner must then be
configured to match the host’s OCIA parameters. Cable installation alone does not guarantee that the StratosS will
communicate properly with the host system.
Configuration bar codes are located in the MetroSelect Configuration Guide
(MLPN 00-02407x) and the
MS2xxx Stratos Series Configuration Addendum (MLPN 00-02034x).
1. Turn off the host system.
2. Plug the 10-pin RJ45 end of the OCIA interface cable (MLPN 57-57016x-N-3) into the 10-pin socket labeled Scanner Host
OCIA on the bottom of the StratosS. Refer to figure on page 23.
3. Connect the other end of the OCIA Interface cable (MLPN 57-57016x-N-3) to the appropriate communication port on the
host device.
Before continuing verify that the OCIA cable pinouts match the host system’s and is connected to the appropriate
interface socket on the scanner. An incorrect cable connection can cause communication problems or potential
damage to the scanner and/or terminal.
Manufacturers Note: Plugging the scanner into the serial port of the host device does not guarantee that scanned
information will appear at the host device. A software driver and correct configuration settings are also required for
proper communication to occur.
4. Plug the external power supply (MLPN 46-002xx) into the 3-pin Molex socket labeled, DC Power In, on the bottom of the
StratosS.
Check the AC input requirements of the power supply to make sure the voltage matches the AC outlet. The outlet
should be located near the equipment and be easily accessible.
Metrologic recommends using a switched AC outlet. The switch should be located on the operator’s side of the
checkout counter in close proximity to the StratosS to facilitate calibration and service of the unit.
5. Connect AC power to the transformer. If the AC outlet is equipped with an on/off switch, turn the power on.
6. Turn on the host system.
7. Configure the StratosS to match the host system’s OCIA parameters.
Refer to the MetroSelect Configuration Guide (
MLPN 00-02407x) under Section I: OCIA for Enabling and Setting
OCIA Parameters.
- MS2221 / MS2222 1
- StratosS 1
- ABLE OF CONTENTS 3
- INTRODUCTION 5
- BASE MODEL CHARACTERISTICS 10
- INSTALLATION 16
- NSTALLATION 20
- SCANNER OPERATION 31
- MAINTENANCE 42
- TROUBLESHOOTING 44
- DEFAULT SETTINGS 47
- SCANNER PINOUT CONNECTIONS 54
- Scale RS232 to Host 55
- Scale to 55
- MLPN 57-57210x-N-3 56
- MLPN 57-57212x-N-3 56
- MLPN 57-57016x-N-3 56
- *, MLPN 57-57008x-N-3 57
- REGULATORY COMPLIANCE 58
- LIMITED WARRANTY 61
- PATENTS 62
- 00-02268B 68
Powiązane produkty i podręczniki dla Czytniki kodów kreskowych Metrologic StratosS MS2220
(50 strony)Rugged-ridge Rear Lower Control Arm Skidplates, 07-14 Jeep Wran podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Do samochodu Rugged-ridge Rear Lower Control Arm Skidplates, 07-14 Jeep Wran.
Dostarczamy 1 pdf podręczników Rugged-ridge Rear Lower Control Arm Skidplates, 07-14 Jeep Wran do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentarze do niniejszej Instrukcji